Kelvion

kelvion png

Cooling Towers

Tundracel


The new Kelvion TUNDRACEL Co-Current Closed Circuit Evaporative Cooling Tower offers a premium quality waste water cooling solution that will boost heat transfer efficiency, while using less energy and water. Plate heat exchangers, cooling towers and dry coolers, in stainless steel designs or with adiabatic cooling, have proven to be efficient solutions for the cooling of process water and also for energy recovery.

Depending on the temperature difference between the water outlet and the ambient temperature, the given air humidity and the process fluid temperature, Kelvion, as an experienced technology leader for process cooling, offers both individual components and efficient system solutions.

TUNDRACEL, the latest innovation in the Kelvion portfolio, uses evaporative cooling to remove heat from a process stream. It is ideal for a wide range of heavy duty industries, including Oil & Gas, Refining, Petrochemical, and Power.

With the co-current closed circuit technology, the air helps to spread the water evenly over the entire surface of the tubes, thereby reducing scaling and fouling. As a result, electricity consumption is lower, reducing your environmental footprint and increasing production capacity.

Water costs are significantly lower with the TUNDRACEL, compared to the conventional cooling tower/PHE solutions, as it operates at high concentration cycles. This increases the number of times water can be reused. Also, our technology is designed to work with water of poor quality, such as blowdown water from a cooling tower, treated waste streams, plant effluent and even sea water, as make-up water.

Factsheet
kelvion png

Cooling Towers

Polacel CMDR Series

Selecting a cooling tower
The water temperatures (hot water in and cold water out), the wet bulb temperature of the site of installation, the required water flow and the noise level are the 4 major factors in order to select a wet cooling tower. After analyzing your needs, we will propose the most appropriate technical and economic solution.There are Polacel CMDR standard solutions for every need starting from a water flow to cool of 90 m3/h. Our engineers can also make special adaptations of the standard cooling towers in order to meet the most specific of your needs.The various type of available heat exchange surfaces allows us to select a suitable fill whether of the “film” type or of the “splash” type . The heat exchange fill is chosen according to the quality of water to be cooled (clean or highly polluted water), but also depending on the specific environment of the site and considering to the process to be cooled. In all cases, a chemical treatment of the cooling water is required. This shall be implemented by a specialized company based on the maximum concentration values ​​advocated by Kelvion.

Polacel CMDR = thermal performance certified by CTI STD-201
The thermal performance of  Polacel CMDR cooling towers from Kelvion B.V. are certified according to the CTI STD-201 standard (Cooling Technology Institute). Certification is the assurance for our customers to have a cooling tower that cools the water at the required temperature. It eliminates costly in-situ performance tests.The Polacel CMDR cooling towers are equipped with axial fans driven by geared motors. The geared motors being usually controlled by variable speed drives, the Polacel CMDR cooling towers thus contribute to the reduction of operational costs (OPEX) of the tower and therefore of your entire installation.

Factsheet
kelvion png

Cooling Towers

Polacel CMC Series

Selecting a cooling tower
The water temperatures (hot water in and cold water out), the wet bulb temperature of the site of installation, the required water flow and the noise level are the 4 major factors in order to select a wet cooling tower. After analyzing your needs, we will propose the most appropriate technical and economic solution. There are Polacel CMC standard solutions for every need starting from a water flow to cool of 90 m3/h. Our engineers can also make special adaptations of the standard cooling towers in order to meet the most specific of your needs. The various type of available heat exchange surfaces allows us to select a suitable fill whether of the “film” type or of the “splash” type . The heat exchange fill is chosen according to the quality of water to be cooled (clean or highly polluted water), but also depending on the specific environment of the site and considering to the process to be cooled. In all cases, a chemical treatment of the cooling water is required. This shall be implemented by a specialized company based on the maximum concentration values advocated by Kelvion.

Polacel CMC = thermal performance certified by CTI STD-201
The thermal performance of  Polacel CMC cooling towers from Kelvion B.V. are certified according to the CTI STD-201 standard (Cooling Technology Institute). This certification is the assurance for our customers to have a cooling tower that cools the water at the required temperature. It eliminates costly in-situ performance tests. The Polacel CMC cooling towers are equipped with axial fans driven by geared motors. The geared motors being usually controlled by variable speed drives, the Polacel CMC cooling towers thus contribute to the reduction of operational costs (OPEX) of the tower and therefore of your entire installation.

Factsheet
kelvion png

Cooling Towers

Polacel CMDI Series

Selecting a cooling tower
The water temperatures (hot water in and cold water out), the wet bulb temperature of the site of installation, the required water flow and the noise level are the 4 major factors in order to select a wet cooling tower. After analyzing your needs, we will propose the most appropriate technical and economic solution. There are Polacel CMDI standard solutions for every need starting from a water flow to cool of 500 m3/h. Our engineers can also make special adaptations of the standard cooling towers in order to meet the most specific of your needs.The various type of available heat exchange surfaces allows us to select a suitable fill whether of the “film” type or of the “splash” type . The heat exchange fill is chosen according to the quality of water to be cooled (clean or highly polluted water), but also depending on the specific environment of the site and considering to the process to be cooled. In all cases, a chemical treatment of the cooling water is required. This shall be implemented by a specialized company based on the maximum concentration values ​​advocated by Kelvion.

Factsheet
kelvion png

Cooling Towers

Polacel CMDIF Series

Selecting a cooling tower
Water temperatures (hot water inlet and cold water outlet), the temperature of the wet bulb at the installation site, the required water flow and the noise level are the 4 main factors in order to select a wet cooling tower. . After analyzing the needs, the most appropriate technical and economic solution will be presented. Polacel CMDIF standard solutions exist for all needs, from water flow to 500 m 3 cooling/H. Our engineers can also make special adaptations to standard cooling towers to meet the most specific needs. The various types of heat exchange surfaces available allow you to select a suitable fill, either “film” or “splash” type. The heat exchange filler is chosen according to the quality of the water to be cooled (clean water) highly polluted), but also depending on the specific environment of the place and considering the process to be cooled. In all cases, a chemical treatment of the cooling water is required. This must be implemented by a specialized company based on the maximum concentration values ​​advocated by Kelvion.

Factsheet
kelvion png

Cooling Towers

Polacel XT, XL Series

Structural qualities
The advanced design engineering has also resulted in a number of special structural advantages:

    • Only a minimum number of support points are necessary as a result of the self-supporting foundations and the high internal rigidity
    • Where possible, fully portable and installed ready to go
    • The Polacel frost-proof polyester water pan can withstand sub-zero temperatures. Essential for free-cooling applications
    • Due to their low profile, cross flow cooling towers present fewer aesthetic problems
    • The expandable modular system has virtually no limitations in terms of shape and size
    • All structural design principles are analysed and tested in advance using dynamic calculations and computer studies

Durable and reliable
We design and manufacture cooling towers that have a long life and require a minimum of maintenance. This performance is achieved by a careful choice of materials – stainless steel combined with glass fibre reinforced polyester and plastics – the exceptionally sound design and the considerable experience of our engineers.

‘Cheap and cheerful’ solutions such as fans with a V-belt drive, or painted panels, are avoided. The result is a cooling tower that is low maintenance, economical and able to deliver a consistently high quality, problem free performance.

Factsheet
kelvion png

Dry Coolers

Kelvion LF-S

Kelvion has re-engineered the popular LF-SJ. We have optimised the coil sizing for new generation fans to get additional benefits of an even higher efficiency coil.

Factsheet
kelvion png

Dry Coolers

Kelvion LV-M

M-height configuration is suitable for many applications: The single row of fans and narrow V angle make it ideal for installation requiring a high capacity density – small footprint.

Factsheet
kelvion png

Dry Coolers

Kelvion LV-T&L

T and L-profile extends the versatility of the V Profile range: With its high thermal capacity, robust framework and low noise levels, plus innovative energy-efficient fan sets, the V-Profile is suited to applications ranging from HVAC, data centers, centralized cryptocurrencies, to power applications (like diesel and gas genset cooling) and industrial cooling.

Factsheet